Go Back   :::.Nissan 4x4 Owners Club.::: > General > Members free classifieds and wanted items.

Members free classifieds and wanted items. Place your Nissan/Ford 4x4 vehicles or related items for sale and wanted here.

Reply
 
Thread Tools Display Modes
Old 11-06-2018, 20:56   #31
Lazy-Ferret
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
Default

Quote:
Originally Posted by george View Post
Always someone negative... Rick has been sent the email

1k pot across pins 2 and 3 on the fuel pump loom, works for Bosch or zexel

Dyno proven 30bhp and 100nm gains
Sorry George, can I just ask a few questions please?

How do you set the pot up for best performance? Is it trial and error, or is there a procedure?

Is it worth mounting the pot on the Dash, so you can wind it up or down, as and when needed, or is it best in a box under the bonnet, so once setup you just leave it alone?

You say across pin 2 and 3, is this connector down on the fuel pump, or one of the ones up on the top of the engine?

Thanks.
Lazy-Ferret is offline   Reply With Quote
Old 11-06-2018, 21:02   #32
jims-terrano
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2004
Location: UK
Posts: 12,965
Default

Tdoug mounted his box on the dashboard. He then plays with his knob as he pleases, that sounds wrong some how. He adjusts it on the fly, got to say it seemed to chuck out a lot of black smoke at times though.

For what it’s worth I didn’t get the impression anyone had been particularly negative or derogatory. Still water under bridge, moved on now.
jims-terrano is offline   Reply With Quote
Old 11-06-2018, 21:03   #33
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

Quote:
Originally Posted by Lazy-Ferret View Post
Sorry George, can I just ask a few questions please?

How do you set the pot up for best performance? Is it trial and error, or is there a procedure?

Is it worth mounting the pot on the Dash, so you can wind it up or down, as and when needed, or is it best in a box under the bonnet, so once setup you just leave it alone?

You say across pin 2 and 3, is this connector down on the fuel pump, or one of the ones up on the top of the engine?

Thanks.
Hiya mate, I can answer at least one of those for you, wires on top of engine, and also I have mine stuck to a blank switch plate next to the central locking unlock button next to steering wheel.
I think I'm doing some underfloor heating tomorrow but not sure how much, if I get time and if you like I will post some pics of wiring and controller!
terranosaurusdoug is offline   Reply With Quote
Old 11-06-2018, 21:07   #34
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

Quote:
Originally Posted by jims-terrano View Post
Tdoug mounted his box on the dashboard. He then plays with his knob as he pleases, that sounds wrong some how. He adjusts it on the fly, got to say it seemed to chuck out a lot of black smoke at times though.

For what it’s worth I didn’t get the impression anyone had been particularly negative or derogatory. Still water under bridge, moved on now.
The smoke is a bonus feature when turned right up great deterrent for tailgaters whack it up and foot down for smoke then turn it back down to normal

Yeh like you said Jim, it's nowt to lose sleep over
terranosaurusdoug is offline   Reply With Quote
Old 11-06-2018, 21:19   #35
Lazy-Ferret
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
Default

Quote:
Originally Posted by Banshee View Post
At what cost though? As most of you know I'm not one scared to try a mod or 5 but by installing said electronics, what other detrimental effects will this have in the long run, or even short term on components including IP, MAF etc.

I'm not knocking the method or saying it can't be done, I just believe in applying a bit of thought and logic to things before jumping into the unknown.

Yes you'll probably see 30BHP increase in performance, but would others have neccasarily thought about the possible legalities of it in terms of insurance for instance?

Given the OP's attitude towards the deconstruction of the "tuning boxes" he was trying to sell, I'd fear fitting said device to my vehicle without fully understanding what it does, and how it works at a component level.

Were said boxes manufactured by someone that knew about electronics at all? Are the devices CE stamped to comply with automotive electronic standards? Highly doubtful to all of the above I guess.

I'm just fussier than your next guy and maybe such interrogation raised the question as to whether I was just trying to rip the box off and start making my own for profit?

Who knows, who cares, end of the day I just want to look out for my fellow forum members and friends.
Not to make light of your concerns, but a Pot (potentiometer) is not really electronics, it's just a variable resistor, which is a passive device. The only issue I can see, is personally, I would probably use a 470ohm resistor in series with a 470ohm Pot, and then put those two components across the two wire, so that even when you wind the pot right down to 0ohm, you can not put a dead short across the wires. This would just be a safety thing for me, as I do not know what the detrimental effects of actually shorting those pins out would be on the ECU.

As for the CE marks and legalities, while again it is a valid concern, this mod is not worse than most other modifications made to these cars. I very much doubt there is a CE mark on, Ray's MAF amp, none of the home made snorkels, roof racks, roof tents, roll out blinds, storage drawers, body lifts, uprated suspension components, winch bumpers, and even most winches.

I think as a Forum Mod, you would be better just adding a Caveat, "Please do not make this modification if you do not know what you are doing, or are not willing to potentially deal with the damage that could be caused to your cars electronic components by making this unsanctioned modification. Please also be aware that modifications such as this could invalidate your warrantee, and insurance. If in doubt, please contact a qualified auto electrician, and your insurance company before trying this modification!"

Otherwise, have fun, and if you are brave enough, let us know how you get on.. Ohhh and to paraphrase Zippy, don't forget the pictures!!!
Lazy-Ferret is offline   Reply With Quote
Old 11-06-2018, 21:22   #36
Lazy-Ferret
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
Default

Quote:
Originally Posted by terranosaurusdoug View Post
Hiya mate, I can answer at least one of those for you, wires on top of engine, and also I have mine stuck to a blank switch plate next to the central locking unlock button next to steering wheel.
I think I'm doing some underfloor heating tomorrow but not sure how much, if I get time and if you like I will post some pics of wiring and controller!
Yes please.... not sure if I will try it, or not, but there are times when towing the caravan I could do with a little more grunt... In all the time I have had it, my car has never put out any black smoke, even on the Welsh hills with the caravan on the back.
Lazy-Ferret is offline   Reply With Quote
Old 11-06-2018, 21:32   #37
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

Quote:
Originally Posted by Lazy-Ferret View Post
Yes please.... not sure if I will try it, or not, but there are times when towing the caravan I could do with a little more grunt... In all the time I have had it, my car has never put out any black smoke, even on the Welsh hills with the caravan on the back.
No probs.
The more I turn it the more smoke it makes, if I leave it at a reasonable setting, which I did but have it a little higher now, I don't notice any smoke. I have it set a tad higher now and notice some smoke on initial acceleration, but it does go faster so it must be burning extra fuel and not just throwing it out the back. The best way to get tailgaters is to slow down and if possible change up a gear to make the engine labour a bit at low revs, then turn the knob and boot it this doesn't work well on motorways though as the revs are too high and the fuel gets burnt instead of turning to smoke!
terranosaurusdoug is offline   Reply With Quote
Old 11-06-2018, 21:35   #38
solarman216
Off road maniac
Click here to find out how to become a paid up member
 
solarman216's Avatar
 
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,298
Default

Sorry have not been following this completely but agree with Clive's point about the 470 ohm resistor, haste to say does not apply to my manual pumped Patrol and the Mrs would not let me play with her T2, Rick
__________________
Ex banger racer now off road maniac
Lokka on the front with manual hubs
Diff lock on rear
3 inch SS straight through exhaust
Manly winch bumper with 13000 lb winch
10 spike ground anchor, with multiple straps and blocks
Super strong body cills capped with scaffold pole
20% stronger springs all round
aggressive off road tyres on wheels so just swap.
Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.
solarman216 is offline   Reply With Quote
Old 11-06-2018, 21:39   #39
george
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jan 2013
Location: Barton upon Humber
Vehicle: swb terrano
Posts: 151
Default

If any one wants installation instructions then please leave your email and I will forward them to you

I personally ran one for 25k turned up as much as my clutch would take and had no issue... it's a big mod in the vw scene just we use a different pin out on the ecu

Before these where offered to sale it was run past the electricians and instrument techs at my work!!

One box was run on a dyno in Australia at a diesel tuning shop!! These are where my figures are from! The shop where very impressed as they mainly deal with big Cummins ect

At the end of the day it's down to the individual, when I first posted here I was told it couldn't be done... well it can and if you want some more power then knock yourself out..
george is offline   Reply With Quote
Old 11-06-2018, 21:41   #40
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

Quote:
Originally Posted by george View Post
If any one wants installation instructions then please leave your email and I will forward them to you

I personally ran one for 25k turned up as much as my clutch would take and had no issue... it's a big mod in the vw scene just we use a different pin out on the ecu

Before these where offered to sale it was run past the electricians and instrument techs at my work!!

One box was run on a dyno in Australia at a diesel tuning shop!! These are where my figures are from! The shop where very impressed as they mainly deal with big Cummins ect

At the end of the day it's down to the individual, when I first posted here I was told it couldn't be done... well it can and if you want some more power then knock yourself out..
I love mine mate, transforms the drive
terranosaurusdoug is offline   Reply With Quote
Old 11-06-2018, 21:42   #41
george
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jan 2013
Location: Barton upon Humber
Vehicle: swb terrano
Posts: 151
Default

Quote:
Originally Posted by Lazy-Ferret View Post
Sorry George, can I just ask a few questions please?

How do you set the pot up for best performance? Is it trial and error, or is there a procedure?

Is it worth mounting the pot on the Dash, so you can wind it up or down, as and when needed, or is it best in a box under the bonnet, so once setup you just leave it alone?

You say across pin 2 and 3, is this connector down on the fuel pump, or one of the ones up on the top of the engine?

Thanks.
Hi if you drop me your email I can send you pics where to wire into

I recommend cab mounted

It is to some extent trial and error to suit each truck and driver... I recommend dialing it down until idle turns lumpy or picks up then knock it back a touch, 9 times out of 10 this will want slight adjustmen after a few miles

On my personal trucks I tend to run one set at a happy medium for every day then install a second one on a switch for full power/smoke

Cheers
george is offline   Reply With Quote
Old 11-06-2018, 21:48   #42
Blocky10
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2014
Location: Welcome to Norwich, a fine city
Vehicle: 2004 Terrano 3.0 SVE Auto
Posts: 3,601
Default

Or buy a 3ltr
Blocky10 is offline   Reply With Quote
Old 11-06-2018, 21:49   #43
Lazy-Ferret
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
Default

Quote:
Originally Posted by george View Post
Hi if you drop me your email I can send you pics where to wire into

I recommend cab mounted

It is to some extent trial and error to suit each truck and driver... I recommend dialing it down until idle turns lumpy or picks up then knock it back a touch, 9 times out of 10 this will want slight adjustmen after a few miles

On my personal trucks I tend to run one set at a happy medium for every day then install a second one on a switch for full power/smoke

Cheers
Thanks
terrano2@lazy-ferret.co.uk
Lazy-Ferret is offline   Reply With Quote
Old 11-06-2018, 22:09   #44
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

Quote:
Originally Posted by Blocky10 View Post
Or buy a 3ltr
....and bring it to Wales
terranosaurusdoug is offline   Reply With Quote
Old 11-06-2018, 22:12   #45
Lazy-Ferret
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
Default

Quote:
Originally Posted by Blocky10 View Post
Or buy a 3ltr


I can't afford the Tax...
Lazy-Ferret is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 19:38.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Images online photo albums