Go Back   :::.Nissan 4x4 Owners Club.::: > General > The Clubs Virtual Pub

The Clubs Virtual Pub For general chat, so come on in and pull up a chair.

Reply
 
Thread Tools Display Modes
Old 11-07-2019, 14:20   #1
Jay666d
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jul 2016
Location: Northumberland
Vehicle: Patrol GU3 (Y61) 3.0 SVE
Posts: 1,375
Default ZD30 - Limp.

I feel like the heading to this thread is more of a statement!

But I have a query/issue that I just don't know the answer too.... And I haven't been able to solve the issue with my Dawes Valve.

Let me set the scene:

In the morning I get in the truck to head of to work. I drive down my road which is a mile long 1st at 20mph, then it turns to 30mph, then to for the last 200 yards leading up to a T-Junction it's national speed limit. (I achieve around 50mph before I have to slow for a bend and then the junction right after.)

I wait at the junction for my time to pull out and when I do, this is where the problem happens.

The Truck is Auto, so it takes care of the gears. As it builds up speed and gets to about 40-45mph and the revs get to about 2500rpm up I'm at around 16psi of boost (Limited by the Dawes to 17psi) all of a sudden progression is halted!

I can keep my foot where it is and I will maintain the exact speed, like its hit a limiter or I can briefly ease off the accelerator, let the revs drop away put my foot back down and carry on gaining speed. (Every now and again, when I ease off and back on again, it might repeat the limiting process... But never more than twice in a row!)

If this is 'Limp Mode' then I thought setting the Dawes to 17psi would eliminate this? As I understand, the ZD30 usually creates 18psi and sometime spikes which causes the Limp Mode to kick in?

So this has me baffled... Any help would be appreciated.
Jay666d is offline   Reply With Quote
Old 11-07-2019, 16:37   #2
Jay666d
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jul 2016
Location: Northumberland
Vehicle: Patrol GU3 (Y61) 3.0 SVE
Posts: 1,375
Default

Reading a couple of posts on the Oz forums, one guy had a similar problem and he replaced the MAF sensor... Might look into changing that.
Jay666d is offline   Reply With Quote
Old 11-07-2019, 17:29   #3
macabethiel
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Aug 2008
Location: Derby
Vehicle: Freelander & Jeep GC 3.0
Posts: 4,415
Angry This is why I hate modern cars !

TBH if either of our Jeeps had that issue I would have no idea where to start aside from obvious things like checking for loose turbo pipes etc.

To date the only no starts I have had with diesels has been flat battery and a recent fully blocked air filter. I am told to leave cleaning sensors to those who know how to do it as they can be damaged easily by the likes of me!

Am sure others here will know how to do some OBD stuff using paper clips & rubber bands.
macabethiel is offline   Reply With Quote
Old 11-07-2019, 17:44   #4
rayf3262
Senior Member
Click here to find out how to become a paid up member
 
rayf3262's Avatar
 
Join Date: Nov 2009
Location: Norfolk, Poringland NR14
Vehicle: Terrano 3.0 SVE 2002
Posts: 1,549
Default

Is the manifold and exhaust system standard?
Mine would drop into limp mode when I had hole in the flexi-joint.
The inrease in gas flow is seen by the MAF and mapped by the ECU software to be in error.

Just another thought, 17PSI is very close to the point where the MAP sensor may come ito play, so a spike into and beyond is another possibility.
__________________
Remember what the dormouse said:
Feed your head....
rayf3262 is offline   Reply With Quote
Old 11-07-2019, 18:44   #5
Barrbeast
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2013
Location: Dundee, Scotland
Vehicle: 1990 4.2 SWB Safari
Posts: 2,615
Default

Sounds like the classic overboost protection system kicking in tbh dude so may be worth a try at dialling the dawes back first before looking at anything that costs

If that doesn't change it then try the MAF?
Barrbeast is offline   Reply With Quote
Old 11-07-2019, 20:23   #6
Mr K
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2015
Location: South Northants
Vehicle: Nissan Patrol Y61 2.8
Posts: 1,145
Default

Have you not just changed your downpipe?

As far as I understand it, the limp mode has nothing to do with the boost you are running, but all to do with what voltage your maf is reading. Hence why some people can run 20psi and some limp out at 15psi.

If your downpipe is in, it is that, if not, it could be the maf. But as rob said I would adjust the boost setup first.

I'd start with the needle valve as it seems it will be your spool up that's changed with the downpipe having a lot less back pressure.
Mr K is offline   Reply With Quote
Old 11-07-2019, 21:24   #7
Jay666d
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jul 2016
Location: Northumberland
Vehicle: Patrol GU3 (Y61) 3.0 SVE
Posts: 1,375
Default

I haven't gotten round to changing my downpipe yet... BUT, my exhaust does currently eng just after the Flexi pipe.

What I'll do is, get my down pipe on, build the rest of my exhaust, then strat adjusting the Dawes valve accordingly.

Thanks for your input guys.
Jay666d is offline   Reply With Quote
Old 11-07-2019, 21:27   #8
Mr K
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2015
Location: South Northants
Vehicle: Nissan Patrol Y61 2.8
Posts: 1,145
Default

Sounds good to me
Mr K is offline   Reply With Quote
Old 11-07-2019, 21:30   #9
Banshee
Moderator
 
Banshee's Avatar
 
Join Date: Jul 2012
Location: West Midlands
Vehicle: 04 2.7 SWB Terrano II Van
Posts: 13,525
Default

MAF or lack of manifold pressure my money
__________________
Moderator

04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread
Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job
Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank
TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger
Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter


99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread
Engine Transplant - In Progress!!!
Banshee is offline   Reply With Quote
Old 12-07-2019, 00:34   #10
Barrbeast
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2013
Location: Dundee, Scotland
Vehicle: 1990 4.2 SWB Safari
Posts: 2,615
Default

I think Martin could be on the money re the needle valve. I never had an issue when I ran my 3.0 for a week with nothing after the downpipe BUT by that point I'd tweaked the vnt stop to reduce the spool rate a bit.

Definitely get the rest of the exhaust fitted then start tweaked dawes and needle.
Barrbeast is offline   Reply With Quote
Old 12-07-2019, 07:24   #11
Jay666d
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Jul 2016
Location: Northumberland
Vehicle: Patrol GU3 (Y61) 3.0 SVE
Posts: 1,375
Default

Yeah, I have also tweaked the VNT, but that was all done before the exhaust came off. (I'm sure the truck did it before I took away the exhaust, but it did have a few cracks in it!)
Jay666d is offline   Reply With Quote
Old 12-07-2019, 16:19   #12
Barrbeast
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2013
Location: Dundee, Scotland
Vehicle: 1990 4.2 SWB Safari
Posts: 2,615
Default

Quote:
Originally Posted by Jay666d View Post
Yeah, I have also tweaked the VNT, but that was all done before the exhaust came off. (I'm sure the truck did it before I took away the exhaust, but it did have a few cracks in it!)
Yeh but I never fitted dawes or needle valves, so it could well be that the spool rate needs tweaked. Possibly the needle valve and vnt adjustment you've done aren't enough.
Barrbeast is offline   Reply With Quote
Old 13-07-2019, 00:25   #13
Davey Boy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Dec 2015
Location: Dartmoor
Vehicle: Patrol ZD30 SVE
Posts: 960
Default

Jay
Every truck is different.
Mine went into limp at 17psi, a horrible sensation!
Dropped to 16psi and never had a problem thereafter.
It won’t hurt to just try it and see for now.
I can give mine a squirt for power and hold onto it with now fear of limp.
Just my thoughts.
D
Davey Boy is offline   Reply With Quote
Old 15-07-2019, 16:31   #14
BigBlue
Junior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2018
Location: Powys
Vehicle: Nissan Y61 Patrol Shorty.
Posts: 24
Default Try this also.

If your engine management light is on off with it too, try getting it obd2 checked, as mine had a knackered throttle position sensor which made driving some days an arse. Limp mode came on all over the place because of it. Replaced mine by changing the whole pedal ass from a wreckers. £30. All good now.
BigBlue is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 13:00.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Images online photo albums