Go Back   :::.Nissan 4x4 Owners Club.::: > General > Show us yours

Show us yours Share you favourite photos with us

Reply
 
Thread Tools Display Modes
Old 15-05-2021, 21:25   #1
Oddball Matt
Junior Member
Click here to find out how to become a paid up member
 
Join Date: Apr 2020
Location: Finland
Vehicle: 1999 Terrano ll 2.7tdi
Posts: 29
Default My rear bumper protector thingy build

A bit of background info... I`m a transport contractor delivering mail, one of my daily tasks is to go fill up the parcel pickup locker downtown so I`ll be needing to load and unload one of these trolleys full of packets daily tipping the trolley in against the rear bumper (I don`t have any rear seats mounted inside)



Problem of course is doing this rubs onto the rear bumper chafing off the paint from the corners of the spare wheel dent/boarding step.



My first attempt was to try beat some diamond plate into submission and make corner protectors but lacking the tools and skills the fit was terrible so I ditched that effort and went with what I know.



A few mild bends to a 1" tube and some 3x30 flat stock for a frame...



...some diamond plate to cover...



...acid primer to prevent rust and some silver to coat...





...and bam we have a new rear bumper protector. Not a bad way to spend a saturday morning methinks. The lower cover plate still needs redone as I fudged up the angles trying to freestyle it and figuring out too late the offcut piece I`m working with is too small so figured I`d make SOMETHING out of it to cover the gap and make a pretty one later. The spare wheel mount holes will also be occupying a jerrycan later, I already have the can but the store had ran out of the mounts so need to order that online, and I need to source a new handle from somewhere as the finger trigger part has broken off so currently operating the mechanism through a wire loop sticking out of the hole, works fine but the jerrycan mount will be covering that so needs sorted at some point.
Oddball Matt is offline   Reply With Quote
Old 15-05-2021, 22:46   #2
solarman216
Off road maniac
Click here to find out how to become a paid up member
 
solarman216's Avatar
 
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,432
Default

Excellent bumper protector, Rick
__________________
Ex banger racer now off road maniac
Lokka on the front with manual hubs
Diff lock on rear
3 inch SS straight through exhaust
Manly winch bumper with 13000 lb winch
10 spike ground anchor, with multiple straps and blocks
Super strong body cills capped with scaffold pole
20% stronger springs all round
aggressive off road tyres on wheels so just swap.
Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.
solarman216 is offline   Reply With Quote
Old 16-05-2021, 09:49   #3
macabethiel
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Aug 2008
Location: Derby
Vehicle: Freelander & Jeep GC 3.0
Posts: 4,416
Thumbs up Neat looking luading area protector

Now that's thinking outside the box - raising the platform is a much tidier solution!
macabethiel is offline   Reply With Quote
Old 16-05-2021, 15:28   #4
Banshee
Moderator
 
Banshee's Avatar
 
Join Date: Jul 2012
Location: West Midlands
Vehicle: 04 2.7 SWB Terrano II Van
Posts: 13,526
Default

I take it you don't intend on carrying a spare wheel on the back door anymore then? or if you are you will need a damn big spacer which will stress the mounting points
__________________
Moderator

04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread
Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job
Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank
TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger
Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter


99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread
Engine Transplant - In Progress!!!
Banshee is offline   Reply With Quote
Old 16-05-2021, 17:33   #5
Oddball Matt
Junior Member
Click here to find out how to become a paid up member
 
Join Date: Apr 2020
Location: Finland
Vehicle: 1999 Terrano ll 2.7tdi
Posts: 29
Default

No I don't even have the mount, the truck came to me without it. I will be mounting a jerry can holder onto the door once it comes in the mail so there will be 20-something kg hanging off the door but right off the surface so not a problem.
Oddball Matt is offline   Reply With Quote
Old 18-05-2021, 17:10   #6
terranosaurusdoug
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
Default

I like it
terranosaurusdoug is offline   Reply With Quote
Old 16-06-2021, 05:58   #7
nimbinbid
Member
Click here to find out how to become a paid up member
 
Join Date: Apr 2011
Location: Australia, NSW
Vehicle: 1999 Terrano II TDI 2.7
Posts: 52
Default

Now that's a professional looking mod. Well done mate!
nimbinbid is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 09:41.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Images online photo albums